Slide Baiting.

Post Options Post Options   Likes (0) Likes(0)   Quote v8-coupe Quote  Post ReplyReply Direct Link To This Post Topic: Slide Baiting.
    Posted: 02 Feb 2017 at 12:16pm
v8-coupe View Drop Down
Titanium
Titanium
Avatar

Joined: 20 Jul 2002
Location: New Zealand
Status: Offline
Points: 4309
Hi.
Thought I would try this here. No response in the general forum.
Am looking at giving this a go.
They say live baits are no problem but cut baits an be hard to get down.
Has anyone used a 1/4oz or similar ball sinker on the trace?
If you have, are there any problems or other recommendations?
Thanks in advance.

Cheers
Graham
Legasea Legend Member
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Zambezi Quote  Post ReplyReply Direct Link To This Post Posted: 07 Feb 2017 at 1:39pm
Zambezi View Drop Down
Titanium
Titanium
Avatar

Joined: 10 Dec 2006
Location: Djibouti
Status: Offline
Points: 4640
Which form of slide baiting? Non-return aka south african style or the free running slider bait clip ring thing?
A man’s comfort in life can be measured by the quality of the toilet paper he uses to wipe his arse.
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote v8-coupe Quote  Post ReplyReply Direct Link To This Post Posted: 07 Feb 2017 at 2:36pm
v8-coupe View Drop Down
Titanium
Titanium
Avatar

Joined: 20 Jul 2002
Location: New Zealand
Status: Offline
Points: 4309
Originally posted by Zambezi Zambezi wrote:

Which form of slide baiting? Non-return aka south african style or the free running slider bait clip ring thing?

Hi.
Have not heard from you in a while.
Some pointed out videos on Youtube with fancy non return sliders. Lost their gear to a hook up. Was thinking of going the cheap snap swivel way until I get a little experience.
Was also going to try a small 1/4ox ball sinker down by the cut bait on the trace to help it slide down.
Some say live baits are ok but cut baits can be a nuisance if you do not have an acute angle.
Thoughts?

Cheers
Graham
Legasea Legend Member
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Slidebaiter Quote  Post ReplyReply Direct Link To This Post Posted: 08 Feb 2017 at 10:43pm
Slidebaiter View Drop Down
Bronze
Bronze


Joined: 20 Aug 2016
Status: Offline
Points: 31
Snap swivels work fine.

There are lots of variations which work.

I started out Fishing with a Ring stopper.

I've use a Swivel then trace to the Sinker. 

I use a Large polystyrene bead above the Swivel on the mainline as a stopper.

The Acute angle is critical when using dead baits....whatever system you use, so if you are sliding in the Surf, longer Rods in Tall Rod holders is a good start 

To answer your question about using lead, you're on to it.

It works, on the Trace just fine, Barrel type sinker is best.

I find keeping the Sinker close to the snap Swivel 'slider' works best.
I Tie  a Slip Bobber Knot below the trace sinker to stop it sliding (lessens tangles, less movement for the Fish to sense somethings up when they first run....which is why the use of a baitrunner reel.


Slide baiting is often done from deep ledges or Piers, so the acute angle is a given.

It works here in the Surf live baiting, but using dead baits on a flat beach ....you're up against it (as you have alluded to already it's all about the Angle, you can't cheat the physics, gravity and friction, Wave action current).


I've only taken up Slide baiting in the last year, and some days it is spectacular (depending on the availability of suitable live baits).


Some tips and pointers for anyone wanting to give this simple fishing method a try:

1. Use a breakaway, breakout sinker ideally, You need good grip which creates the tension in a taught line that makes sliding possible.

2. No need for complicated expensive equipment, try slide baiting so you understand the principles, then make it work for your local conditions using quality but affordable terminal gear.

3.  Yellow tails, Yellow tails, Yellow tails. If you get them, the ideal is using recurve hooks bridle rigged (rubber band or cable ties work) *you can nose hook them with something small and strong like the KS 4 Black Magic pattern. If you cant get them, the myriad of live small fish species, or juveniles of other species will do.



4. 14'6 inches of Rod is a good start.

5. A Baitrunner reel fished in Baitrunner mode.

As with all live baiting the Rod tip will betray the baits level of fear.

Typically nods of the rod tip are followed by line moving in an unmistakable fashion. As line steadily peels off....it is not long before the reel starts screaming, at which point you open the bail arm for minimal disruption of the take....this usually leads to bait being swallowed.

Picture what is happening under water, the break out sinker stays where you cast it....thereby allows for the baitrunner to let the Fish run by creating a bow of line.

Circle hooks come in handy when you engage the reel, quite often the fish is hooked before the rod loads up (steadily increased pressure from all that line the fish is starting to tow the faster/further it runs).

I let the fish go for ages before engaging.




Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote v8-coupe Quote  Post ReplyReply Direct Link To This Post Posted: 09 Feb 2017 at 12:33pm
v8-coupe View Drop Down
Titanium
Titanium
Avatar

Joined: 20 Jul 2002
Location: New Zealand
Status: Offline
Points: 4309
Originally posted by Slidebaiter Slidebaiter wrote:

Snap swivels work fine.

There are lots of variations which work.

I started out Fishing with a Ring stopper.

I've use a Swivel then trace to the Sinker. 

I use a Large polystyrene bead above the Swivel on the mainline as a stopper.

The Acute angle is critical when using dead baits....whatever system you use, so if you are sliding in the Surf, longer Rods in Tall Rod holders is a good start 

To answer your question about using lead, you're on to it.

It works, on the Trace just fine, Barrel type sinker is best.

I find keeping the Sinker close to the snap Swivel 'slider' works best.
I Tie  a Slip Bobber Knot below the trace sinker to stop it sliding (lessens tangles, less movement for the Fish to sense somethings up when they first run....which is why the use of a baitrunner reel.


Slide baiting is often done from deep ledges or Piers, so the acute angle is a given.

It works here in the Surf live baiting, but using dead baits on a flat beach ....you're up against it (as you have alluded to already it's all about the Angle, you can't cheat the physics, gravity and friction, Wave action current).


I've only taken up Slide baiting in the last year, and some days it is spectacular (depending on the availability of suitable live baits).


Some tips and pointers for anyone wanting to give this simple fishing method a try:

1. Use a breakaway, breakout sinker ideally, You need good grip which creates the tension in a taught line that makes sliding possible.

2. No need for complicated expensive equipment, try slide baiting so you understand the principles, then make it work for your local conditions using quality but affordable terminal gear.

3.  Yellow tails, Yellow tails, Yellow tails. If you get them, nose hook them with something small like the KS 4 Black Magic pattern. If you cant get them, the myriad of live small fish species, or juveniles of other species will do.

4. 14'6 inches of Rod is a good start.

5. A Baitrunner reel fished in free spool.

As with all live baiting the Rod tip will betray the baits level of fear.

Typically nods of the rod tip are followed by line moving in an unmistakable fashion. As line steadily peels off....it is not long before the reel starts screaming, at which point you open the bail arm for minimal disruption of the strike.

Picture what is happening under water, the break out sinker stays where you cast it....thereby allows for the baitrunner to let






Excellent.
Thank you very much.
I have practiced making up the rigs.
Your suggestion about the sinker being kept near the swivel of the sliding trace makes perfect sense when you think about it.
Is there any reason I could not have the snap swivel, short length of mono with small barrel sinker, another swivel then the trace? More knots and places of weakness I guess.
Will look up the Slip Bobber knot.
Feel a little more confident now with the set up.
Will give it a go soon and report back.

Thanks to all.
Cheers
Graham
Legasea Legend Member
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Slidebaiter Quote  Post ReplyReply Direct Link To This Post Posted: 09 Feb 2017 at 1:16pm
Slidebaiter View Drop Down
Bronze
Bronze


Joined: 20 Aug 2016
Status: Offline
Points: 31


[/QUOTE]

Excellent.
Thank you very much.
I have practiced making up the rigs.
Your suggestion about the sinker being kept near the swivel of the sliding trace makes perfect sense when you think about it.
Is there any reason I could not have the snap swivel, short length of mono with small barrel sinker, another swivel then the trace? More knots and places of weakness I guess.
Will look up the Slip Bobber knot.
Feel a little more confident now with the set up.
Will give it a go soon and report back.

Thanks to all.
Cheers
Graham[/QUOTE]
Look forward to hearing how you get on.

Your double swivel idea will work just fine.

Personally I like using shorter traces for the tangle factor (about a foot long).

I edited that first post to talk about Circle hooks (they are how slide baiting is really meant to work) but I found nose hooking with very fine point heavy gauge Smaller KS 4/0 sets just fine under all that load, provided you give the fish plenty of line.

Dead baits I would go circle hook every time, you don't want to gut hook Illegal stuff.

You will get some funny looks from onlookers....chucking lead into the ocean with no bait or hook.....



Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote v8-coupe Quote  Post ReplyReply Direct Link To This Post Posted: 09 Feb 2017 at 1:51pm
v8-coupe View Drop Down
Titanium
Titanium
Avatar

Joined: 20 Jul 2002
Location: New Zealand
Status: Offline
Points: 4309
Originally posted by Slidebaiter Slidebaiter wrote:





Excellent.
Thank you very much.
I have practiced making up the rigs.
Your suggestion about the sinker being kept near the swivel of the sliding trace makes perfect sense when you think about it.
Is there any reason I could not have the snap swivel, short length of mono with small barrel sinker, another swivel then the trace? More knots and places of weakness I guess.
Will look up the Slip Bobber knot.
Feel a little more confident now with the set up.
Will give it a go soon and report back.

Thanks to all.
Cheers
Graham[/QUOTE]
Look forward to hearing how you get on.

Your double swivel idea will work just fine.

Personally I like using shorter traces for the tangle factor (about a foot long).

I edited that first post to talk about Circle hooks (they are how slide baiting is really meant to work) but I found nose hooking with very fine point heavy gauge Smaller KS 4/0 sets just fine under all that load, provided you give the fish plenty of line.

Dead baits I would go circle hook every time, you don't want to gut hook Illegal stuff.

You will get some funny looks from onlookers....chucking lead into the ocean with no bait or hook.....



[/QUOTE]

Thanks.
Info on hooks and length of trace noted.
Any recommendations on the length between the break out sinker and stop swivel?
Cheers
Legasea Legend Member
Back to Top
Post Options Post Options   Likes (1) Likes(1)   Quote Fissure Quote  Post ReplyReply Direct Link To This Post Posted: 09 Feb 2017 at 1:58pm
Fissure View Drop Down
Titanium
Titanium
Avatar

Joined: 30 Oct 2007
Location: Wellington
Status: Offline
Points: 4351
maybe tie some elastic band around the trace below the sinker to stop it sliding?

Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Slidebaiter Quote  Post ReplyReply Direct Link To This Post Posted: 09 Feb 2017 at 5:23pm
Slidebaiter View Drop Down
Bronze
Bronze


Joined: 20 Aug 2016
Status: Offline
Points: 31
Originally posted by v8-coupe v8-coupe wrote:

Originally posted by Slidebaiter Slidebaiter wrote:





Excellent.
Thank you very much.
I have practiced making up the rigs.
Your suggestion about the sinker being kept near the swivel of the sliding trace makes perfect sense when you think about it.
Is there any reason I could not have the snap swivel, short length of mono with small barrel sinker, another swivel then the trace? More knots and places of weakness I guess.
Will look up the Slip Bobber knot.
Feel a little more confident now with the set up.
Will give it a go soon and report back.

Thanks to all.
Cheers
Graham

Look forward to hearing how you get on.

Your double swivel idea will work just fine.

Personally I like using shorter traces for the tangle factor (about a foot long).

I edited that first post to talk about Circle hooks (they are how slide baiting is really meant to work) but I found nose hooking with very fine point heavy gauge Smaller KS 4/0 sets just fine under all that load, provided you give the fish plenty of line.

Dead baits I would go circle hook every time, you don't want to gut hook Illegal stuff.

You will get some funny looks from onlookers....chucking lead into the ocean with no bait or hook.....



[/QUOTE]

Thanks.
Info on hooks and length of trace noted.
Any recommendations on the length between the break out sinker and stop swivel?
Cheers[/QUOTE] length mainly depends on your casting style and the platform/area you arecasting length wise. A meter is minimum e.g some overhead casting styles have pretty short lengs of line,(you don't want your bait closer to the bottom than that in any case.)....after that it comes down to what you feel comfortable casting
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Toad Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2017 at 3:12am
Toad View Drop Down
Silver
Silver


Joined: 30 Aug 2002
Status: Offline
Points: 490
Hi Slidebaiter, how strong is your polystyrene bead (I suppose it would be strong) if it's working as your stopper? If it did break (probably very unlikely), then the slider would be pulled down, over the swivel, down to the wire eye of the BOS sinker - which would then stop the slider? I have heard someone say (think it was Chad Prentice, who knows his stuff) he doesn't bother with a stopper arrangement if fishing a clean beach - the sinker is his stopper.
Another guy, who'd obviously done a bit of slide baiting, showed me his rig at a tackle shop. He used a rubber bead above a biggish snap swivel to make his stopper. The snap swivel he clipped to the wire eye of the sinker (no line between the swivel and sinker). I didn't think the swivel looked very strong - it wasn't all that big, but he said it was actually a good thing that the snap was fairly weak. It would give him a chance to break free from the sinker if snagged. He thought it was important the snap swivel was there to give a little bit of distance between the hook trace and the wire grips on the sinker, when the slider was at the bead. He was worried about the trace tangling with them, maybe because he fished live bait. He also used a pretty heavy trace, mostly for its stiffness, so it wouldn't tangle.  
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Slidebaiter Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2017 at 10:34am
Slidebaiter View Drop Down
Bronze
Bronze


Joined: 20 Aug 2016
Status: Offline
Points: 31
Originally posted by Toad Toad wrote:

Hi Slidebaiter, how strong is your polystyrene bead (I suppose it would be strong) if it's working as your stopper? If it did break (probably very unlikely), then the slider would be pulled down, over the swivel, down to the wire eye of the BOS sinker - which would then stop the slider? I have heard someone say (think it was Chad Prentice, who knows his stuff) he doesn't bother with a stopper arrangement if fishing a clean beach - the sinker is his stopper.
Another guy, who'd obviously done a bit of slide baiting, showed me his rig at a tackle shop. He used a rubber bead above a biggish snap swivel to make his stopper. The snap swivel he clipped to the wire eye of the sinker (no line between the swivel and sinker). I didn't think the swivel looked very strong - it wasn't all that big, but he said it was actually a good thing that the snap was fairly weak. It would give him a chance to break free from the sinker if snagged. He thought it was important the snap swivel was there to give a little bit of distance between the hook trace and the wire grips on the sinker, when the slider was at the bead. He was worried about the trace tangling with them, maybe because he fished live bait. He also used a pretty heavy trace, mostly for its stiffness, so it wouldn't tangle.  

The Polystyrene beads I use do get destroyed under heavy load, or have impression marks. Quite often the Snap Swivels will only travel through one another on the correct angle (does happen and the Sinker Stops the whole lot as you said). The beads slowly work their way back up the line until you deploy the panicked Live bait, they do slow the descent of the Live Bait somehat (Which I find desirable through the Water Column).

All good points, the simplified rig you describe is interesting because it makes a lot of sense for slide baiting application over clean ground using live baits.

Thanks for adding the tough trace tip. Heavier Fluro carbon is pretty stiff so that helps with this type of fishing, but is not essential, any stiff Trace is the go. Small live yellow tails are attractive to big toothy critters as we know.

If I am fishing in snag prone areas then I tend to use a weaker length of breakaway line to the Sinker for the same reason the bloke you mentioned uses a weaker Snap direct to the Sinker. Also change sinker type.

From a Wharf that needs a long cast to access a main channel, I take the 14" 6" Rod and use a sensible line weight to the Sinker (to avoid flying sinkers)

Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Toad Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2017 at 12:24pm
Toad View Drop Down
Silver
Silver


Joined: 30 Aug 2002
Status: Offline
Points: 490
Thanks a lot Slidebaiter. Where do you get the polystyrene beads? I guess they are the same as what's used as small floats on surfcasting traces.
The guy who used a snap swivel directly attached to his sinker, he used a non-return slide - a Tackle Tactics one. His hook trace must have been 100 pounds, maybe more - to me it looked heavy. He made it using crimps. He didn't use a leader - he tied his mainline to the snap swivel clipped to the sinker. He didn't seem to think he needed a leader (and was probably concerned a joining knot between mainline & leader could be a snagging point for the slider). He used 30 lb mainline.
I didn't like the look of his snap swivel to begin with - they are famous for being a bit weak. But it's the snap that's fairly weak, the swivel itself would be fairly strong. A hooked kingfish would not be pulling on the snap part of the swivel (if used as a sinker attachment). And even if the snap did break (because of a snag or casting force, maybe), the bead would still be stopped by the swivel itself.
I still don't really like that set up. I think the traditional solid ring stopper is probably better. It's often a solid ring and swivel joined together - hard to find for sale, might have to be made by yourself. 
I think when slide-baiting at river mouths, the rig doesn't have to be complicated at all. Your casts are short, the kingfish are in close. It doesn't matter much if the live bait doesn't get all the way down to the end of the line. You're unlikely to be burnt off.
Using a fairly normal surf rod and reel, the terminal tackle probably doesn't have to be super strong - you can't put that much pressure on it. But I still don't like snap swivels. I don't think I'd use a cheap one as a slider. I've got some Black Magic ball bearing snap swivels - one of them would do as a slider.   
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Slidebaiter Quote  Post ReplyReply Direct Link To This Post Posted: 10 Feb 2017 at 2:31pm
Slidebaiter View Drop Down
Bronze
Bronze


Joined: 20 Aug 2016
Status: Offline
Points: 31
Excellent points Toad.

The whole point of using slide baiting with live baits is that it is superior to all other forms of live baiting, when placing your bait by casting is required.

The unique scenario of catching Kingfish from the surf in NZ is well understood.

By experimenting I've found other applications here in our conditions.

1. You want to fish away from Wharf Piles with 30lb mainline, or you want to cast from that type of location into a Harbour main channel,....in conditions where a Balloon etc won't work.
If you live in a city like Auckland where I am, being able to live bait from a Crowded Wharf into a main channel is where slide baiting comes into its own.

Fishing 30Lb mainline while live baiting is deadly for strike rate relative to 50lb + conventional styles.

Off a Snaggy Rock platform, it again allows you to cast just beyond all the foul that holds fish, which is ideal on days where Balloons and floats, or John Dory dropper type rigs aren't really workable.

3. Fishing 30lb Line off the Bricks live baiting, demands you place your bait away from the foul. Conventional wisdom is that u fish your feet, but if you have an oily Burley mix......you're going to be in the Zone, or near enough to it, to pick up passers by, and for residents to respond to the signals (the main reason I use the float style surfcasting Styrene beads is the bling factor....a thrashing live bait makes a red ball very visible I imagine.).

30lb live baiting off the Rocks or Wharf means you need the fish to go away from you, in the foul...that's where letting the fish have lots of line before engaging is beneficial.

Some finer points on the take with this method are:

In baitfeeder mode, some live baits are too active, so you have to dial up the bottom drag. Current in good locations demands this also.

Like all baitrunner fishing, the least drag you can get away with the better....but even When I've got into a King off a Wharf in high tidal current, at first the tension is fairly high....but the way you respond to that first inquiry is critical (I'll talk about this a bit more later).

Once your Live bait settles (the slow swim Down to the ring in slide baiting settles the Live bait better than the artificial trapped near the surface by floating effect, or fixed to a dropper type scenario.

Most of the time I'm fishing with the bottom drag partially dialed up for the reasons outlined.

As soon as the bait starts panicking (rod tip nods) you know your baits gone from settling after slidding ( it takes a couple of minutes at least for the bait to hit the stopper on a long cast) to being activrley pursued.

I get ready for that first steady pulling of line, then immediately dial down the bottom drag to full bait runner mode.


Invariably the speed of the line moving increases with less resistance by a lot.

Lastly I pick the rod out of the holder carefully and point it at the fish, opening the bail arm.

That is three stages of decreasing resistance,, which entices aggressive behavior.

In My experience when the Fish first takes the bait, I recon it knows it is attached to something, but is hungry enough to have a go anyway and trys to out power the resistance.

Then when you dial down the bottom drag,you are telling the fish it is winning, which gives the Fish positive feedback.

Opening the bail arm, 9 times out of ten it goes nuts and runs away from you at ever increasing speed.

In other words I think the progression of freedom entices more aggressive behaviour, and more simple to deal with, 'open water" type escapes than the tough and dirty Hard style over foul behavior from big predators.

Once you engage the bail arm, by the time the fish reaches the end of all that bowed line, a six ounce Sinker is embedded in the bottom of the sea floor, and all that monno is enough resistance for a circle hook to roll and set...or a sharp point J Hook to break out of the bait with a smooth lift of the rod when you see the tip loading up.

As you say, slide bating over clean areas like River Mouths allows for this essentially lighter line form of live baiting to come into its own.

If I'm targeting Kings or Big Snapper in the Surf, I'm happy enough with a 60lb trace....since if its live bait, even Big Snaps are less likely to get trace between their teeth with a mouth full of Live bait.

The guy you mention using heavy trace, Im curious as to whether he is from overseas (SouthAfrica and Hawaii Slide baitnig is more common) in the tropics you are more likely to hook razor toothed game fish.

I haven't hooked Bronzies here, or Barracouta yet....so 100Lb type trace hasn't been needed.

Excuse the rant, but hooking Kings slide baiting, generally means you are going to play them gentle style, 7kg max drag pressure, as opposed to Locked up18Kg drag pressure of other forms of live baiting, which reinforces why a reasonable quality snap swivel will hold.

Sliding gets you into areas with live baits that other forms do not.

Slidding with dead baits is by the by, and I'm guessing out fished by other methods.

I've clipped dead bait to Fixed ring Slide bait set ups while I wait to land my first Livey.

In Hawaii the only reason they slide dead baits is because fishermen are shoulder to shoulder in deep water.
They need to keep casting and retrieving to a minimum, so they cast once, and keep clipping on traces until they hook up (I've never treid this to be fair, there must be some untangling involved).

Like all fishing methods, you can't judge based on your 1st attempt (I got no joy and wasted a year till I tried again).

My first success was an 8kg KY. That same session I landed four large Ky on live baits from a wharf while bait fishos got nothing.

That got me into slide baiting wherever I can set a live bait while I do other stuff.

If you hook up it is always something decent with liveys, and the fishing on light gear is always explosive and Violent.

BTW topcatch have large Solid rings if you have a store in your location.

Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote jaypeegee Quote  Post ReplyReply Direct Link To This Post Posted: 11 Feb 2017 at 3:03am
jaypeegee View Drop Down
Platinum
Platinum
Avatar

Joined: 22 Aug 2010
Location: Neo Tea Roa
Status: Offline
Points: 1503
Hi


I use the following:

Mainline with either a large plastic bead or 2cm long latex tube with an id of 1mm to protect the mainline knot tied to an SS ring
The ring is tied to a rotten bottom clip I made.

Basically just 1.6 mm wire I use for lure making that is twisted into two loops with the end of the wire bent out forming a clip .Like a small half u shape.
Imagine you're making a swivel shaped thing I guess where the half u clip sticks out from the middle

There maybe better ways to make these but that's the best way I know and it has been mainly reliable


Make two of these so one clip points up and the other down. The bottom of the clips should hang from the top clip and will be in this position when you cast.
Tie the bottom loop of the top clip to the top loop of the bottom clip with light line. This should be light enough to easily break if a substantial fish is on but strong enough to hold your drag given the line should be tight and straight as possible.

Tie the other side of the ring that you attached to the mainline to the top of the the rotten bottom rig with the same breaking strain as the leader or mainline you are using.
Attach the bottom of the rotten bottom rig to the sinker again using the same breaking strain line.

The distance from the sinker to SS ring measured with the rotten bottom rig unclipped can be whatever length you want but it can be hard to cast if it's too long as the sinker can't touch the ground when you cast so I make the light line that joins the rotten bottom rig about half the total so when the clip is closed I have a metre long drop and when unclipped it is up too two metres.

Whatever the length of the sinker to SS ring section is I will make this longer than the trace I attach the livie to. I have used a sinker attached directly to the ring but this too often ends up with the livie wrapping line around the sinker spikes. I may be missing something obvious here so feel free to let me know if there is a way to combat this.

Fuque, it's late and I'm tire. I'll edit later to make sense

I used this set up the other day and it came back with a wee fishie and no sinker as desired. It's neighbour rod which got no hits came back complete with sinker.


"You don't have to be smart to laugh at a fart, but you have to be stupid not to."
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Slidebaiter Quote  Post ReplyReply Direct Link To This Post Posted: 12 Feb 2017 at 4:39pm
Slidebaiter View Drop Down
Bronze
Bronze


Joined: 20 Aug 2016
Status: Offline
Points: 31
Originally posted by jaypeegee jaypeegee wrote:

Hi


I use the following:

Mainline with either a large plastic bead or 2cm long latex tube with an id of 1mm to protect the mainline knot tied to an SS ring
The ring is tied to a rotten bottom clip I made.

Basically just 1.6 mm wire I use for lure making that is twisted into two loops with the end of the wire bent out forming a clip .Like a small half u shape.
Imagine you're making a swivel shaped thing I guess where the half u clip sticks out from the middle

There maybe better ways to make these but that's the best way I know and it has been mainly reliable


Make two of these so one clip points up and the other down. The bottom of the clips should hang from the top clip and will be in this position when you cast.
Tie the bottom loop of the top clip to the top loop of the bottom clip with light line. This should be light enough to easily break if a substantial fish is on but strong enough to hold your drag given the line should be tight and straight as possible.

Tie the other side of the ring that you attached to the mainline to the top of the the rotten bottom rig with the same breaking strain as the leader or mainline you are using.
Attach the bottom of the rotten bottom rig to the sinker again using the same breaking strain line.

The distance from the sinker to SS ring measured with the rotten bottom rig unclipped can be whatever length you want but it can be hard to cast if it's too long as the sinker can't touch the ground when you cast so I make the light line that joins the rotten bottom rig about half the total so when the clip is closed I have a metre long drop and when unclipped it is up too two metres.

Whatever the length of the sinker to SS ring section is I will make this longer than the trace I attach the livie to. I have used a sinker attached directly to the ring but this too often ends up with the livie wrapping line around the sinker spikes. I may be missing something obvious here so feel free to let me know if there is a way to combat this.

Fuque, it's late and I'm tire. I'll edit later to make sense

I used this set up the other day and it came back with a wee fishie and no sinker as desired. It's neighbour rod which got no hits came back complete with sinker.


I think it's pretty cool you make your own breakaway system, it is quite hard to describe something visual folk like me haven't seen before, that doesn't have broad terms of reference to compare to.

A pic would be great (of your half U shaped clips) if you can manage it please.

I don't think you are missing anything when you found attaching the SS Ring directly to sinker = tangled livey.......Unless the Live bait gets nailed before it hits the sinker, you are always going to risk entanglement.

Out of interest....have you hooked any strinrays on a Live bait that can swim to the Sinker ?

The reason I ask is that I'm not prejudice against sport fishing (land and release) big rays or full grown eagle rays....which fight harder than some kingfish....if River Monsters can makes TV series including Rays....then I figure in a country like ours....they are a target.

Fishing records are hard to come by, but I imagine that a dedicated slide baiter will eventually compete over sand with light line....against some of the boat light tackle records.....food for thought slidebaiters....because Live bait = big fish.
Back to Top
Post Options Post Options   Likes (1) Likes(1)   Quote Zambezi Quote  Post ReplyReply Direct Link To This Post Posted: 20 Feb 2017 at 7:59pm
Zambezi View Drop Down
Titanium
Titanium
Avatar

Joined: 10 Dec 2006
Location: Djibouti
Status: Offline
Points: 4640
Here's something I wrote a few years back.

http://www.nzfishingworld.co.nz/latest/2015/08/slidebaiting-begginers-guide

It will get you 80% of the way for non-returns, covers the high level basics.
A man’s comfort in life can be measured by the quality of the toilet paper he uses to wipe his arse.
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote v8-coupe Quote  Post ReplyReply Direct Link To This Post Posted: 21 Feb 2017 at 12:25pm
v8-coupe View Drop Down
Titanium
Titanium
Avatar

Joined: 20 Jul 2002
Location: New Zealand
Status: Offline
Points: 4309
Originally posted by Zambezi Zambezi wrote:

Here's something I wrote a few years back.

http://www.nzfishingworld.co.nz/latest/2015/08/slidebaiting-begginers-guide

It will get you 80% of the way for non-returns, covers the high level basics.


Ha ha ha. Read that article. Did not realize it was you. Age creeping up on me. :-)

As an aside. Gave it a crack off a wharf last weekend. Made a stupid nooby error. There were a few people there and without considering the tide, I set up. You guessed it. Was not long before other peoples sinkers were rolling over/under my line. Gave up after an hour as there were no spots available where I needed to be. Sigh! Lesson learned.
Legasea Legend Member
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Zambezi Quote  Post ReplyReply Direct Link To This Post Posted: 21 Feb 2017 at 2:20pm
Zambezi View Drop Down
Titanium
Titanium
Avatar

Joined: 10 Dec 2006
Location: Djibouti
Status: Offline
Points: 4640
What a bugger, I've been given an old slide setup which can cast up to 10oz, finally have my hands on an old SST50.

Slowly rebuilding kit.
A man’s comfort in life can be measured by the quality of the toilet paper he uses to wipe his arse.
Back to Top
Forum Jump
Forum Permissions View Drop Down


This page was generated in 0.398 seconds.

Fishing Reports Visit Reports

Saltwater Fishing Reports
Raglan Fishing Report - 12/11/26

Big spring snapper. With the more settled weather over the last couple of weeks there’s... Read More >

12 Nov 2026
Saltwater Fishing Reports
Mercury Bay Fishing Report - 12/11/26

Snapper hit and miss. Most reports have been telling us it’s becoming more difficult to... Read More >

12 Nov 2026
Saltwater Fishing Reports
Northland Fishing Report - 12/11/26

The switch has been flicked on! Call it what you want, El Niño, global warming,... Read More >

12 Nov 2026
Saltwater Fishing Reports
Tauranga Fishing Report - 12/11/26

Snapper and kahawai in close. Again, we start on a positive note, with some nice... Read More >

12 Nov 2026
Fishing bite times Fishing bite times

Major Bites

Minor Bites

Major Bites

Minor Bites