Calcutta 400B service

Post Options Post Options   Likes (0) Likes(0)   Quote Kandrew Quote  Post ReplyReply Direct Link To This Post Topic: Calcutta 400B service
    Posted: 31 Mar 2020 at 7:50pm
Kandrew View Drop Down
Titanium
Titanium


Joined: 16 Apr 2012
Status: Offline
Points: 4152
Hi guys

I’m gunna have a go at servicing my Calcutta any tips or things to watch out for.

Cheers
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote OuttaHere Quote  Post ReplyReply Direct Link To This Post Posted: 01 Apr 2020 at 10:07am
OuttaHere View Drop Down
Platinum
Platinum


Joined: 05 Oct 2015
Location: NZ
Status: Offline
Points: 2712
They are fiddly little bastards.

Getting the plastic inner plate (the "Set plate") thing back into the right hand sideplate with everything in the state it's supposed to be in, ugh.

Also the bearing the spool shaft runs on can get very very stuck in the sideplate, at both ends. If you decide to do the spool bearings, be super super careful removing the spool pin on the right hand side, it's very easy to slightly bend the spool shaft and then you're up for a new spool.

Schematic is here:

A common mod is to replace the driveshaft bushing with a ball bearing.
Also worth checking if you have the updated clutch bar assembly (see bottom left corner of schematic) - although good luck getting one out of Shimano at the moment.

Watch out for corrosion under the handle arm, and behind the handle arm nut retainer.

Be careful not to get grease on the anti-reverse bearing or it will slip. Lightly oil it at the most.

If parts were actually available... I'd also consider replacing the handle assembly with one off a Calcutta 400BSV. Big upgrade over the paddles, especially if yours have gone "gummy".
Back to Top
Post Options Post Options   Likes (1) Likes(1)   Quote shaneg Quote  Post ReplyReply Direct Link To This Post Posted: 02 Apr 2020 at 9:25pm
shaneg View Drop Down
Titanium
Titanium
Avatar

Joined: 12 Jul 2009
Location: New Zealand
Status: Offline
Points: 4948
there a lot of bits in those .. why don’t you courier it to swordfish Steve or Greg at Gofish. I took a 200d apart once and couldn’t put back together after getting beach dumped at campbells. That said you could be way more capable and meticulous.
Back to Top
Forum Jump
Forum Permissions View Drop Down


This page was generated in 0.305 seconds.

Fishing Reports Visit Reports

Saltwater Fishing Reports
Top of the South Fishing Report - 23/01/26

Snapper, cod and marlin on the menu Despite the weather we have had recently, when... Read More >

23 Jan 2026
Saltwater Fishing Reports
Bream Bay Fishing Report - 23/01/26

Snapper out deep in cooler water As happens at this time of the year, the... Read More >

22 Jan 2026
Saltwater Fishing Reports
Inner Hauraki Gulf Fishing Report - 23/01/26

Small snapper the norm Over the last 10 years I have noticed with great concern the... Read More >

22 Jan 2026
Freshwater Fishing Reports
Rotorua Fishing Report - 23/01/26

Fishing will be exceptional when water clears The massive amount of rainfall to hit the... Read More >

22 Jan 2026
Saltwater Fishing Reports
Hauraki Gulf Fishing Report - 23/01/26

New year, new action The magic 100m line off Great Barrier has been producing the... Read More >

22 Jan 2026
Freshwater Fishing Reports
Canterbury Fishing Report - 23/01/26

Fantastic surfcasting As per usual, I am writing this near the deadline, and it is... Read More >

22 Jan 2026
Fishing bite times Fishing bite times

Major Bites

Minor Bites

Major Bites

Minor Bites