Zambezi wrote:Which form of slide baiting? Non-return aka south african style or the free running slider bait clip ring thing? |
Slidebaiter wrote:Snap swivels work fine. There are lots of variations which work. I started out Fishing with a Ring stopper. I've use a Swivel then trace to the Sinker. I use a Large polystyrene bead above the Swivel on the mainline as a stopper. The Acute angle is critical when using dead baits....whatever system you use, so if you are sliding in the Surf, longer Rods in Tall Rod holders is a good start To answer your question about using lead, you're on to it. It works, on the Trace just fine, Barrel type sinker is best. I find keeping the Sinker close to the snap Swivel 'slider' works best. I Tie a Slip Bobber Knot below the trace sinker to stop it sliding (lessens tangles, less movement for the Fish to sense somethings up when they first run....which is why the use of a baitrunner reel. Slide baiting is often done from deep ledges or Piers, so the acute angle is a given. It works here in the Surf live baiting, but using dead baits on a flat beach ....you're up against it (as you have alluded to already it's all about the Angle, you can't cheat the physics, gravity and friction, Wave action current). I've only taken up Slide baiting in the last year, and some days it is spectacular (depending on the availability of suitable live baits). Some tips and pointers for anyone wanting to give this simple fishing method a try: 1. Use a breakaway, breakout sinker ideally, You need good grip which creates the tension in a taught line that makes sliding possible. 2. No need for complicated expensive equipment, try slide baiting so you understand the principles, then make it work for your local conditions using quality but affordable terminal gear. 3. Yellow tails, Yellow tails, Yellow tails. If you get them, nose hook them with something small like the KS 4 Black Magic pattern. If you cant get them, the myriad of live small fish species, or juveniles of other species will do. 4. 14'6 inches of Rod is a good start. 5. A Baitrunner reel fished in free spool. As with all live baiting the Rod tip will betray the baits level of fear. Typically nods of the rod tip are followed by line moving in an unmistakable fashion. As line steadily peels off....it is not long before the reel starts screaming, at which point you open the bail arm for minimal disruption of the strike. Picture what is happening under water, the break out sinker stays where you cast it....thereby allows for the baitrunner to let |
Slidebaiter wrote: |
v8-coupe wrote:
Excellent. Thank you very much. I have practiced making up the rigs. Your suggestion about the sinker being kept near the swivel of the sliding trace makes perfect sense when you think about it. Is there any reason I could not have the snap swivel, short length of mono with small barrel sinker, another swivel then the trace? More knots and places of weakness I guess. Will look up the Slip Bobber knot. Feel a little more confident now with the set up. Will give it a go soon and report back. Thanks to all. Cheers Graham |
Toad wrote:Hi Slidebaiter, how strong is your polystyrene bead (I suppose it would be strong) if it's working as your stopper? If it did break (probably very unlikely), then the slider would be pulled down, over the swivel, down to the wire eye of the BOS sinker - which would then stop the slider? I have heard someone say (think it was Chad Prentice, who knows his stuff) he doesn't bother with a stopper arrangement if fishing a clean beach - the sinker is his stopper. Another guy, who'd obviously done a bit of slide baiting, showed me his rig at a tackle shop. He used a rubber bead above a biggish snap swivel to make his stopper. The snap swivel he clipped to the wire eye of the sinker (no line between the swivel and sinker). I didn't think the swivel looked very strong - it wasn't all that big, but he said it was actually a good thing that the snap was fairly weak. It would give him a chance to break free from the sinker if snagged. He thought it was important the snap swivel was there to give a little bit of distance between the hook trace and the wire grips on the sinker, when the slider was at the bead. He was worried about the trace tangling with them, maybe because he fished live bait. He also used a pretty heavy trace, mostly for its stiffness, so it wouldn't tangle. |

jaypeegee wrote:Hi I use the following: Mainline with either a large plastic bead or 2cm long latex tube with an id of 1mm to protect the mainline knot tied to an SS ring The ring is tied to a rotten bottom clip I made. Basically just 1.6 mm wire I use for lure making that is twisted into two loops with the end of the wire bent out forming a clip .Like a small half u shape. Imagine you're making a swivel shaped thing I guess where the half u clip sticks out from the middle There maybe better ways to make these but that's the best way I know and it has been mainly reliable Make two of these so one clip points up and the other down. The bottom of the clips should hang from the top clip and will be in this position when you cast. Tie the bottom loop of the top clip to the top loop of the bottom clip with light line. This should be light enough to easily break if a substantial fish is on but strong enough to hold your drag given the line should be tight and straight as possible. Tie the other side of the ring that you attached to the mainline to the top of the the rotten bottom rig with the same breaking strain as the leader or mainline you are using. Attach the bottom of the rotten bottom rig to the sinker again using the same breaking strain line. The distance from the sinker to SS ring measured with the rotten bottom rig unclipped can be whatever length you want but it can be hard to cast if it's too long as the sinker can't touch the ground when you cast so I make the light line that joins the rotten bottom rig about half the total so when the clip is closed I have a metre long drop and when unclipped it is up too two metres. Whatever the length of the sinker to SS ring section is I will make this longer than the trace I attach the livie to. I have used a sinker attached directly to the ring but this too often ends up with the livie wrapping line around the sinker spikes. I may be missing something obvious here so feel free to let me know if there is a way to combat this. Fuque, it's late and I'm tire. I'll edit later to make sense I used this set up the other day and it came back with a wee fishie and no sinker as desired. It's neighbour rod which got no hits came back complete with sinker. |
Zambezi wrote:Here's something I wrote a few years back. http://www.nzfishingworld.co.nz/latest/2015/08/slidebaiting-begginers-guide It will get you 80% of the way for non-returns, covers the high level basics. |
Big spring snapper. With the more settled weather over the last couple of weeks there’s... Read More >
Snapper hit and miss. Most reports have been telling us it’s becoming more difficult to... Read More >
The switch has been flicked on! Call it what you want, El Niño, global warming,... Read More >
Snapper and kahawai in close. Again, we start on a positive note, with some nice... Read More >