Create Profile or Log In

Forum Menu

Home > Forum Home > General Forums > Tech Topics

Resurrecting old surfcaster

  New Posts New Posts RSS Feed - Resurrecting old surfcaster Forum Search Events FAQ FAQRegister RegisterLogin Login

 Post Reply Post Reply
Post Options Post Options   Likes (0) Likes(0)   Quote Mc Tool Quote  Post ReplyReply Direct Link To This Post Topic: Resurrecting old surfcaster
    Posted: 05 Sep 2023 at 12:58pm
Mc Tool View Drop Down
Silver
Silver


Joined: 23 Dec 2021
Location: Riverton
Status: Offline
Points: 124
I have an old solid glass surfcaster that all the rings are mashed on . Got new rings from Marine deals  and the plan is to  fit em all , But  the varnish or whatever it is painted over the rod is pealing / bubbling off  in places so Im thinkin  some sort of fibreglass friendly stripper may be the go , and what do I spray onto fibreglass to replace this coating , before or after I fit the rings  ( Im  using Fuji a grade polyester thread and clear epoxy  to stick them on ). 
Any hints or tip from those who have done a bit of this would be appreciated .
I wish I was young again .... Id be heaps smarter than this time
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Fish Addict Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 1:30pm
Fish Addict View Drop Down
Platinum
Platinum


Joined: 05 Jul 2009
Location: Perth WA
Status: Offline
Points: 2180
An old blunt knife seems to be the way to go to remove the peeling varnish. 
Have a read here:
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote Tzer Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 3:14pm
Tzer View Drop Down
Titanium
Titanium
Avatar

Joined: 02 Jun 2004
Location: Gisborne. NZ
Status: Offline
Points: 5418
Originally posted by Mc Tool Mc Tool wrote:

I have an old solid glass surfcaster that all the rings are mashed on . Got new rings from Marine deals  and the plan is to  fit em all , But  the varnish or whatever it is painted over the rod is pealing / bubbling off  in places so Im thinkin  some sort of fibreglass friendly stripper may be the go , and what do I spray onto fibreglass to replace this coating , before or after I fit the rings  ( Im  using Fuji a grade polyester thread and clear epoxy  to stick them on ). 
Any hints or tip from those who have done a bit of this would be appreciated .

If your using flexi-coat on your threads then you can use it to re-coat the whole rod with it, just make sure its only a thin coat unlike what you would put on the threads. It pays to be able to have the rod slowly turning as the flex-coat is drying to get nice even looking finish, I have with some rods I have repaired just gone striaght over the existing rod finish and you would hardly notice the underneath coating..
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote smudge Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 5:56pm
smudge View Drop Down
Moderator - Ninja
Moderator - Ninja
Avatar

Joined: 17 Jul 2002
Location: Te Toro
Status: Offline
Points: 31583
You will need to make or borrow a rod lathe to do a good job. I have done some very amateur type rebuilds and it's not a patch on a pro job
Best gurnard fisherman in my street
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote smudge Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 5:58pm
smudge View Drop Down
Moderator - Ninja
Moderator - Ninja
Avatar

Joined: 17 Jul 2002
Location: Te Toro
Status: Offline
Points: 31583
Ohhh I forgot, it would be far cheaper to buy a good surf rod new, but that's not the point and I get that.
Best gurnard fisherman in my street
Back to Top
Post Options Post Options   Likes (0) Likes(0)   Quote lawabidingpoacher Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 8:08pm
lawabidingpoacher View Drop Down
Silver
Silver


Joined: 03 Apr 2021
Status: Offline
Points: 267
Over the years I made a lot of rods , spin , surf ,fly and everything in-between. Always had trouble when it came time to coat bindings etc . We were doing a sheep on the spit one day and it clicked , a quick totoo on dad's lathe and an adaptor to hold a rod was made . A little more time and some rollers were produced. That was a long ways ago , but I still have that spit motor , but no time for building rods or cooking sheep ! .
Back to Top
 Post Reply Post Reply
Forum Jump
Forum Permissions View Drop Down


This page was generated in 0.219 seconds.

Most Thanked Forum Posts

3 Trailer backing lessons
3 Good grunter on a micro jig
3 tauranga fishing
3 Moving to Australia
2 Moving to Australia
2 Trailer backing lessons
2 Drone fishing reports
2 Catchelot
2 Good grunter on a micro jig
2 Snorkel gear

Fishing Reports Visit Reports

Bream Bay Fishing Report - 21/09/23

Fishing becoming consistent As we approach the end of September, the fishing is becoming a... Read More >

Raglan Fishing Report - 21/09/23

Great fishing out deeper Good fishing still prevails in the 70-meter-plus depths due to the... Read More >

Otago Fishing Report

West Coast best coast Sometimes you’ve just got to hit the open road.   Last... Read More >

Top of the South Fishing Report - 21/09/23

Waiting for weather Spring is definitely here. The blossoms are out, the days are much... Read More >

Fishing bite times Fishing bite times

Major Bites

Minor Bites

Major Bites

Minor Bites

All information © 2023 The Fishing Website