Print Page | Close Window

SWR meter required?

Printed From: The Fishing Website
Category: General Forums
Forum Name: Tech Topics
Forum Description: IT - Computers, software, phones, ISP's....
URL: https://www.fishing.net.nz/forum/forum_posts.asp?TID=85330
Printed Date: 22 Nov 2026 at 7:25am


Topic: SWR meter required?
Posted By: mouthu
Subject: SWR meter required?
Date Posted: 29 Nov 2012 at 3:21pm
Anyone got a SWR meter I can borrow in west auckland?
 
If you have to ask what one is, you ain't got one.
 
The reason i  need one is i'm receiving on my vhf but my transmit is crap.


-------------
Yes it was me, I screwed it up for everyone.



Replies:
Posted By: Jet_ski_fisher
Date Posted: 29 Nov 2012 at 4:00pm
Check the radio out and the connections and cable first. because the vhf ant comes factory tunned. if you cut the copper wire you detune it...not a good thing. and a swr meter will only work if you can cut the copper wire to retune it to get the lowest point on the needle..

-------------
http://www.legasea.co.nz" rel="nofollow">
MH... Catch measure release...<*))))<


Posted By: mouthu
Date Posted: 29 Nov 2012 at 5:37pm
I know how to use a swr meter.

-------------
Yes it was me, I screwed it up for everyone.


Posted By: Jet_ski_fisher
Date Posted: 29 Nov 2012 at 6:05pm
Thats good :) have fun

-------------
http://www.legasea.co.nz" rel="nofollow">
MH... Catch measure release...<*))))<


Posted By: Bay Marine Electronics
Date Posted: 30 Nov 2012 at 10:29pm
Bring it down to Tauranga and we'll test it for ya!

Thats not actually true about cutting the coax leading to the antenna, so long as its longer than about a metre long your sweet as (actually so long as its above a half wavelength, I'm too tired to look it up). Cutting the antenna on the other hand....

If you're recieving clearly from a long range you'll probably find the antenna SWR is ok too, if the antenna is buggered then you'll normally stop recieving as well.


-------------
0800 BAY MARINE www.baymarineelectronics.co.nz


Posted By: Jet_ski_fisher
Date Posted: 30 Nov 2012 at 11:31pm
Correct BME.. but i never typed cutting the cable. only the copper wire that is wrapped around the antenna. I'll bet that it's the cable and or the connection eg plu259. hope they get it fixed been in the same boat and found my one was the unit it's self.. 

-------------
http://www.legasea.co.nz" rel="nofollow">
MH... Catch measure release...<*))))<


Posted By: mouthu
Date Posted: 01 Dec 2012 at 8:33am
To give you guys an idea if I know what I'm doing, try this on for size...
 
One of my previous 'hobbies' inlcude an antenna with a half wavelenghtof 18 feet sitting on a mastr 46 feet above the horizon on the north shore of auckland with a red light at the top of the mast so flying objects didn't hit it.
I could tune the whole set up from either the plug into the back of my set or the tuning coil at the base of the anettena, bitharder doing that when it's vertical.
 
I could go into how much db loss I had but no one cares.
 
So, as i can't find my swr metre and a few other things like my soldering iron....
 


-------------
Yes it was me, I screwed it up for everyone.


Posted By: mouthu
Date Posted: 14 Dec 2012 at 1:22pm
Just had Mike from Western Auto and Marine here lloking at my set up, good bloke, turns out it's not the antenna at all............. the radio has a fault that only a swr meter would have picked up.
 
Thanks Rob , Bay Marine Electronics, you were right and thanks for the referral.
 
Have spoken to Uniden who made the radio and gave them the serial number and it's still under warranty even though I didn't buy it new.
 
It gets better.


-------------
Yes it was me, I screwed it up for everyone.


Posted By: Jet_ski_fisher
Date Posted: 14 Dec 2012 at 2:22pm
well done and good on uniden for backing up there products. i bet it was the power output side of it that failed...

-------------
http://www.legasea.co.nz" rel="nofollow">
MH... Catch measure release...<*))))<



Print Page | Close Window