Print Page | Close Window

Lowrance Elite 5 Chirp

Printed From: The Fishing Website
Category: General Forums
Forum Name: Tech Topics
Forum Description: IT - Computers, software, phones, ISP's....
URL: https://www.fishing.net.nz/forum/forum_posts.asp?TID=114142
Printed Date: 20 Nov 2026 at 9:50am


Topic: Lowrance Elite 5 Chirp
Posted By: Boyo
Subject: Lowrance Elite 5 Chirp
Date Posted: 05 Nov 2015 at 12:05pm
Last year when I purchased my boat I negotiated an upgrade from the Lowrance HDS 5 that was on it to an Elite 5 Chirp. The performance of the device is not what I would expect from a Chirp sounder so I am wondering if the dealer I bought the boat from has simply changed out the sounder and re-used the transducer. Is there any way I can tell if the transducer is the right one and if not are there any good transducers you don't need a mortgage for to retrofit.
 
Cheers.



Replies:
Posted By: Bay Marine Electronics
Date Posted: 05 Nov 2015 at 2:05pm
The elite chirp are supposed to chirp the existing lowrance transducers, so the old transducer should work as well as the new one. The elite range is the entry level and the performance is not as good as the true chirp units we have seen. Which is probably to be expected given the price tag.

We have also had a couple of elite chirp units have a bung transducer from the box, so this is also a possibility.


-------------
0800 BAY MARINE www.baymarineelectronics.co.nz


Posted By: Boyo
Date Posted: 05 Nov 2015 at 7:38pm
It does work after a bit of experimentation but not as good as the Garmin chirp model a mate has.


Posted By: Boyo
Date Posted: 02 Dec 2015 at 9:50pm
I have another question regarding my Lowrance Elite. When I first started using it I found I had to keep moving the cross lines (for lack of the correct description) to track the boat position. After awhile I stumbled upon a setting that allowed the boat travelling to track automatically but now unfortunately I have inadvertently changed the setting so that I need to move the cursor again. How to I set it to track automatically? Also how can I change the brightness level? 


Posted By: Muppet
Date Posted: 03 Dec 2015 at 5:49am
Classic case of not reading instruction book? LOL Or have a play at home with it.

Press power button you should get brightness level on the window options that pop up.


Posted By: Bay Marine Electronics
Date Posted: 03 Dec 2015 at 12:05pm
On Chart page hit menu -> top option should be "return to vessel"

pushing the power button for a short push will cycle between backlight levels, holding it in turns the unit on/off




-------------
0800 BAY MARINE www.baymarineelectronics.co.nz


Posted By: Boyo
Date Posted: 03 Dec 2015 at 2:24pm
Muppet -  Thanks for your reply. I was looking in the menus pages as I expected to find it as per the sample dialog on page 7 so I didn't notice it in the buttons description menu.
I spend my day every day resolving industrial breakdowns. I don't mind putting my hand up for advice to expedite a resolution - after all isn't that what this forum is all about. What was your pearl of wisdom regarding the position tracking?
 
Bay Marine Electronics - Thanks very much for your help! I'm pretty sure I went through all the Chart pages and didn't find a "Return to Vessel" option and there is nothing about it in the PDF I am looking at, at the moment. I will have another look in the device at home tonight. Keep up the good work!!!


Posted By: Boyo
Date Posted: 11 Jan 2016 at 10:37pm
This one is for Bay Marine Electronics. Thanks very much for your last assistance. Since I have had my Lowrance I have experienced problems with failure of the sounder under passage then continued failure when stopped. Usually when the sounder has failed the last successful depth detection flashes on the screen. Sometimes it begins detection again but often I have to fiddle with settings and even power reset to achieve operation again. This is very inconvenient when approaching shallow channels. What can I do to overcome this?


Posted By: Bay Marine Electronics
Date Posted: 12 Jan 2016 at 10:41am
You could have  a number of things wrong - possibly transducer placement, possibly faulty transducer or a bad connection. The flashing depth means it is searching for the bottom, so the range will be changing until it finds the bottom again, which can take some time even in perfect conditions. You can get around this by using the unit in manual range (if you know the approximate depth) which will speed up the time it takes to find the bottom again.


-------------
0800 BAY MARINE www.baymarineelectronics.co.nz


Posted By: Boyo
Date Posted: 12 Jan 2016 at 12:16pm
Once again, Bay Marine Electronics, thanks for your helpful assistance. What would be the ideal transducer placement?


Posted By: Big Manly Yaka
Date Posted: 12 Jan 2016 at 12:19pm
Ive recently replaced my Elite 4x standard 83/200 with a new Chirp unit (old one was faulty) and kept the same standard transducer. I have been out half a dozen trips now and its seems to work ok in Chirp mode, maybe a little better in Medium Chirp than High, but to be honest I've ended up going back to the standard 200Hz. When I was running it split screen 200/Chirp the Chirp side would quite often not pick up a lot of the sign that the 200 would.
Maybe I don't know what I'm doing with it but I'm quite happy just running it on the 200 at the moment.


Posted By: Sufishent
Date Posted: 12 Jan 2016 at 1:20pm
I've got an Elite 5 HDI (previous model). Have a perhaps similar (quirky) issue - when in Auto depth mode the sounder sometimes gets confused in "wash" type conditions eg reversing, crossing wakes, aerated water and loses contact with the bottom. To resolve the problem Lowrance recommend putting the sounder into a Manual depth setting suitable to maximum depth - the sounder then "re-finds" the bottom and then its back to normal. Fix has worked well for me.

Have a page of Lowrance recommended "best settings" - if you send me a PM with your email address I'll send it to you. 


-------------
You can never have enough fishing tackle


Posted By: Boyo
Date Posted: 14 Mar 2016 at 10:27pm

Bay Marine Electronics here is another problem I need your assistance on with regards to my Elite 5 Chirp. Recently when I turn it on I cannot acknowledge the start up messages and, of course, because they are still present I can't move on to the menus. I know that the software is out of date as I have downloaded the new version which has a newer version number than that loaded in my device. I thought I would update the software to help resolve my start up issues but it says on the Lowrance website that you need to down load the new version onto a micro SD card that is not bigger than 2GB (where the hell do you get one that size now days), the smallest I could get is 4GB. I tried loading the new version to my device from my 4GB card but it did not work. So I tried reformatting the SD card to FAT system instead of FAT32 but that hasn't worked either. Can you offer any advice - is my start up problem resolvable by updating the software and how can I do it without a 2GB SD card.

As always your help is gratefully accepted. 



Posted By: Bay Marine Electronics
Date Posted: 15 Mar 2016 at 8:50am
In the past we have just bought old cards off trademe when we need a small size, its the cheapest and easiest way to get around that problem, but I realise it wont be available forever!


-------------
0800 BAY MARINE www.baymarineelectronics.co.nz


Posted By: Boyo
Date Posted: 15 Mar 2016 at 9:32am
A friend at work has come up with a couple of smaller cards to try so I'll let you know how I get on. To be honest I have just about had enough of this product and I am about ready to move on. What other brand would you recommend?


Posted By: Chip'n
Date Posted: 15 Mar 2016 at 10:44pm
I bought a 2gb sd card from Jaycar electronics, but they had to get it in for me overnight from their main store. hope that helps.


Posted By: Boyo
Date Posted: 16 Mar 2016 at 4:17pm
Thanks for the suggestion Chip'n. I got it loaded on to a 256mb card and now the upgrade is done.


Posted By: out2sea
Date Posted: 02 Apr 2016 at 3:37pm
Does anyone have recommended or best settings to use for a elite 5 chirp to get best imaging I have the standard 83/200 455/800 Transducer. 

The only issue I have been having is the sounder losing the bottom at speed. I can find it again by manually selecting a depth range then going back to auto. I have tried moving the transducer up and down however it has not been able to completely eliminate the problem and it still happens every 5-10 minutes or at sudden depth changes this is the best I have been able to get it.


Posted By: mands
Date Posted: 02 Apr 2016 at 6:27pm
I have just been researching the Lowrance elite 7Ti and that can come with the TotalScan transducer. Will yours will with that? Seems to be the better transducer than the stock std package


Posted By: Boyo
Date Posted: 02 Apr 2016 at 11:45pm
Earlier on in this thread Sufishent offered me the recommended best settings for an Elite 5 HDI. I had pm'd him but he hasn't got back to me with them yet.


Posted By: Steps
Date Posted: 03 Apr 2016 at 9:03am
I have an eite 5 HDI.
background set to blue
I run a separate gps unit
have the speed setting on fast.
The gain.. lowrance call it something else (interference?) used to have on auto, but after going to an excellent seminar at the boat club recently, playing with this .. minor fine tune for each trip.. change in water temps, water clairty and stuff... so far the fine tune makes a little difference.. enough not to put back on auto still to decide....
everything else is auto
split screen so have one on magnification (wish was more than 2x like my old huminbird)
 the other normal auto depth, and
the other on down scan.
most of our fishing is 2 to 50 m.
All works well thru to 35 mph+


Posted By: out2sea
Date Posted: 03 Apr 2016 at 9:35am
Thanks Steps I will try out settings and see how it goes.


Posted By: Sufishent
Date Posted: 03 Apr 2016 at 5:26pm
Originally posted by Boyo Boyo wrote:

Earlier on in this thread Sufishent offered me the recommended best settings for an Elite 5 HDI. I had pm'd him but he hasn't got back to me with them yet.

Sorry Boyo - no PM received. Here they are:

Best Elite 5/7-HDI Broadband Sounder Settings

Step 1: Press menu twice and go to sonar, change fresh water setting to general.

Step 2: Press pages and select full sonar screen

Step 3: Leave sensitivity and range in auto

Step 4: Leave frequency in 200kHz, but you may want to run dual frequency so change to 83/200kHz

Step 5: Ping speed - Fastest

Step 6: Sonar Options – Noise rejection and surface clarity – Low (Advanced mode will have to be selected for this option to be available. You will have to press menu twice and go into settings in the sonar menu to select advanced menu.

Step 7: Sonar Options – Colour – Blue fish reveal

Note: If customers want to sit in their boat and lean how to use the unit tell them to select stop sonar when the unit is operating out of water with the transducer plugged in. Remember to turn off stop sonar once finished.

DONE!!

Best Elite 5/7-HDI DownScan Sounder Settings

Step 1: Press pages and select full DownScan screen

Step 2: Leave contrast and range in auto

Step 3: Change frequency to 800kHz

Step 4: Ping speed - Fastest

Step 5: Downscan options – Noise rejection and surface clarity to low

Step 6: Colour – Blue gradient

DONE!!!





-------------
You can never have enough fishing tackle


Posted By: Boyo
Date Posted: 04 Apr 2016 at 8:04pm
Hey Sufishent, thanks very much for your info and my apologies for believing I had PM'd you. I did some investigating and as you said, there was nothing in my outbox - must have neglected to press the send button.



Print Page | Close Window