Gamefishing - Crimping techniques

:: Sleeve styles ::

There are three main types of crimp sleeve in common use.
1. Round section
2. Oval section
3. Double barrel

Round section
The less said about these the better. They are usually made from brass and are compressed with a point to cup type crimp tool. They don’t make a strong join but are just about adequate for some light tackle applications. If you’re desperate and can’t tie a knot use these.

Oval section
This style is in almost universal use on commercial longline vessels, and they catch some pretty big fish using them. They are available in various brass and copper alloys and in aluminium and you will need a cup to cup type crimp tool to compress them. These are an excellent choice for serious anglers. When appropriately sized for the leader in use and compressed with the correct tool they create a very strong and reliable connection. Bear in mind though that in saltwater two dissimilar metals can set up a corrosive reaction and if aluminium sleeves are used to join steel cable they will corrode away in a remarkably short period of time, just like the sacrificial anodes used on sea going boats.

For this reason aluminium sleeves should only be used for joining monofilament, whilst brass or copper sleeves can be used for joining either monofilament or cable.

Double barrel
Double barrel sleeves are my favourite. They make a strong neat join and there is no danger of the cable or monofilament crossing over itself inside the sleeve.

They are also in common use on longline boats, but due to being very slightly more costly than oval sleeves they are less popular. Longliners use an awful lot of sleeves so every cent saved is important, but that’s not really such an issue for charter captains or private anglers who use far fewer.

Like oval sleeves, double barrel sleeves are available in both brass or copper and in aluminium. They should also only be compressed with a cup to cup style crimping tool.

The same comments regarding corrosion apply as for oval sleeves. It’s important so I’ll say it again. Use aluminium sleeves for monofilament only, use brass or copper sleeves for either monofilament or steel cable.

Double barrel sleeves are available in both standard and heavy-duty models. The standard sleeves are only available in brass or copper, whilst the heavy-duty sleeves are available in brass, copper and aluminium. These heavy-duty sleeves are for use with heavier leaders and larger crimping tools and are often generically referred to as ‘Nicopress’ sleeves.

:: Crimping tool styles ::

Left hand Point to Cup, right hand cup to cup

There are four major types of crimping tool that you are likely to see.

1. Point to cup
2. Cup to cup standard duty
3. Cup to cup heavy duty
4. Cup to cup bench press

Point to cup
These tools can be purchased relatively cheaply from tackle shops around the world. They resemble a large pair of pliers with semi circular cut outs on one jaw and a series of pointed teeth on the opposite jaw which match up with the opposing cups.

They are used with round section crimp sleeves and they roughly flatten the sleeve around the leader without forming fully around the leader.

They make a very inadequate connection and are not suited to rigging for big fish. I guess you can tell that I don’t much like these.

Cup to cup
I’ll discuss these together because the principle is the same for all of them.

Again they resemble a large pair of pliers, but the opposing jaws have matching pairs of semi circular cut outs (the cups). There are usually three or four different sized cut outs depending on the brand of tool.The jaws usually have markings to indicate the appropriate sized sleeves to use with each cut out. Each cut out will usually accommodate several different sized sleeves either oval section or double barrel.

Standard duty tool
These usually accommodate standard sleeves up to around 2.0 mm — 2.2 mm diameter, good enough for 300 — 400 lb monofilament or 600 lb cable. For most anglers this should be all you’ll ever need.

Heavy duty tool
These are a more costly version of the standard tool, built to much heavier standards and capable of handling standard and heavy duty sleeves as large as any angler is ever likely to need. These are usually found on charter boats, in tackle shops and in the workshops of serious heavy tackle anglers.

Bench press tool
These use pretty much the same jaws as the heavy duty tools but have an extended handle and are bench mounted to facilitate crimping large quantities of heavy sleeves. They are not portable and are reasonably expensive so are usually only used by tackle companies, some larger tackle shops and commercial longline vessels.

:: Making a basic crimped connection in monofilament ::

Take your monofilament leader and select a suitable sleeve. This can be alloy or copper, oval or double barrel, whatever you like, but it should fit snugly over the mono whilst still sliding easily.

Pass the mono through the sleeve, make a loop and pass it back through the sleeve in the opposite direction. Pull an extra 2 or 3 inches through the sleeve.

Take a cigarette lighter and melt the tag end of the mono. When it softens and starts to turn into a ball press the melted end against the lighter or other hard surface to spread and flatten it.

Pull the leader back through the sleeve and the flattened mono end will sit snugly against the end of the sleeve without pulling back through. Now you can adjust the size of the loop.

Left correct — note the uncompressed centre section and the flared ends of sleeve. Right incorrect — the sleeve has been compressed in the wrong direction damaging the monofilament

Take your crimp tool and select the appropriate cut out to suit your sleeve. Position the sleeve between the jaws of the tool so that the concave faces of the cups bear against the curved edges of the sleeve. Do not crimp all the way to the ends of the sleeve as this will cause the edge of the sleeve to cut into the monofilament. Make sure that you have left about 1/16 inch (1.6 mm) between the end of the sleeve and the tool.

Squeeze the tool tightly closed and the sleeve should compress around the monofilament. If using a small sleeve you will only need to crimp it once, but larger sleeves may require that you move the tool along and crimp it once or twice more along its length. If possible leave a 1/16 inch (1.6 mm) space between each compressed portion of the sleeve, and the same at each end. The sleeve should have a flared appearance at each end.

If using this technique to attach hooks, swivels or any kind of anti chafe tube or loop protector you’ll need to remember to thread the leader through them before passing it back through the sleeve and crimping it closed.

:: Making a basic crimped connection in cable ::

Making a crimped connection in cable is pretty much the same as with monofilament, but there are a couple of important differences.

1. Use brass or copper sleeves only. It doesn’t matter whether they’re oval or double barrel.

2. Ensure that you don’t leave an exposed tag end of wire, this can cut you badly when you are leadering a fish. You may need to use a second sleeve crimped over the tag end to achieve this, just pass a couple of extra inches of leader through the first sleeve before crimping it tight. Then either wrap the tag end around the main leader before crimping them with the second sleeve, or if you’re feeling clever you can haywire twist the two lengths of cable before crimping.

:: Common crimping mistakes ::

1. Crimping all the way to the end of the sleeve
This causes the edge of the sleeve to cut into the monofilament, always leave about 1/16 inch (1.6 mm ) uncrimped at each end of the sleeve.

2. Using alloy sleeves on stainless steel cable
As previously mentioned this causes rapid corrosion of the alloy sleeve quickly weakening the joint.

3. Using the wrong size sleeve
It’s pretty much impossible to use too small a sleeve, the leader just won’t fit inside it. However it is possible to use too large a sleeve.

The purpose of crimping is to deform the metal of the sleeve around the leader and not to simply crush the crimp until it touches the leader in as many places as possible. Choose a sleeve that is a comfortable snug fit on your chosen leader material.

Using the wrong tool will cause the joint to fail under pressure

4. Not using the correct crimping tool for the sleeves in use or not using a crimping tool at all
We’ve all met the guy who isn’t prepared to waste his hard earned Dollars on the right tool for the job. He says that he can do just as good a job with pliers, a bench vice, a hammer, his hands, his teeth or whatever.

Well they can’t, that’s the beginning and the end of it.

Monofilament will be damaged by all these methods and whilst cable is more forgiving the individual strands can also be damaged. These methods will produce a joint that sometimes holds up to average fish but will fail when pushed to the limit.

When you consider that a standard crimp tool costs less than 1/20 of the price of a standard trolling charter and should last at least 10 years it seems a false economy to use anything else.

I’ve never seen a correctly crimped connection fail. Fish can be lost for all sorts of reasons but this needn’t be one of them.

Right	Wrong

5. Using the correct tool incorrectly
Many people think that a cup to cup crimping tool should be used with the metal ridges between the semi circular cups pressing into the central groove between the two barrels of a double barrel sleeve or into the flat surfaces of oval sleeves.

This is wrong, the pressure is exerted by the curved surfaces of the cups against the curved sides of the sleeve.

6. Leaving a tag end protruding from the sleeve
This isn’t a big problem with monofilament although it does look untidy and catches on weed and debris in the water.

If you can’t avoid a tag end use a crimp protector to cover the join.
Cable is a different story though. A tag end of wire can cut you badly when you are leadering a fish. Always ensure that the tag ends are covered by a sleeve.

7. Not crimping the sleeve
Unbelievable but true, it’s very easy to be distracted and forget to actually crimp the sleeve! I’ve done it, but hopefully having read this you won’t!

Story by Leadertech

An original article written for The Fishing Website - Fishing.net.nz Ltd It may not be re-published elsewhere without express permission. Copyright Fishing.net.nz Ltd. All rights reserved